8 CANDIDATE QUIZ BUZZER USING 8051 MICROCONTROLLER AT89C51 PDF

Faukree Note, however, that if lock bit 1 is programmed, EA will be internally latched on reset. External pull-ups are required during program verification. After this is done, click the icon debug again to come out of the debug mode. EA should be strapped to VCC for internal program executions. The project can be created in any of the drives available.

Author:Moshicage Zolosar
Country:Great Britain
Language:English (Spanish)
Genre:Music
Published (Last):1 March 2008
Pages:168
PDF File Size:13.65 Mb
ePub File Size:13.63 Mb
ISBN:979-2-48085-433-3
Downloads:32754
Price:Free* [*Free Regsitration Required]
Uploader:Shaktikasa



The team which presses the buzzer earliest is entitled to give the answer. At times it becomes very difficult to identify which team has pressed the button when two teams press the buzzer within a very small time gap. In such cases the decision can be biased due to human intervention.

The quiz buzzer presented here takes care of the aforesaid problem. This quiz buzzer disables the other inputs as soon as the first buzzer is pressed. This quiz buzzer can be used for a maximum of eight teams. This quiz buzzer system has eight input pins corresponding to eight teams. The output is displayed on a seven segment display interfaced with microcontroller , which shows the number corresponding to the team which has pressed the button first.

A buzzer is also sounded for a small duration to give an acoustic alarm. The connections of the seven segment, input pins and output pins is shown in the circuit diagram. There are a total of nine input pins. Eight pins of port P1 of the microcontroller are corresponding to eight inputs and one stop pin for resetting the buzzer system. On the output side a seven segment is connected to display the corresponding output number.

There is also a provision for sounding a buzzer for a small duration. The microcontroller keeps scanning the input pins. As soon as any one of the inputs is pressed, the buzzer sounds for a small duration. The seven segment displays the number corresponding to the input pressed. Now even if any other input pin is pressed, there will be no effect on the system till the time the stop pin is pressed to reset the system.

GURMAT SIDHANT PDF

8 Candidate Quiz Buzzer Using At89c51 Microcontroller

But these voltages cannot be obtained directly. Thus the a. This is done by a transformer. Thus, a step down transformer is employed to decrease the voltage to a required level. Rectifier The output from the transformer is fed to the rectifier. It converts A. The rectifier may be a half wave or a full wave rectifier.

QISAS AND DIYAT ORDINANCE 1990 PDF

Quiz Buzzer Circuit using 8051 Microcontroller and 555 Timer

The team which presses the buzzer earliest is entitled to give the answer. At times it becomes very difficult to identify which team has pressed the button when two teams press the buzzer within a very small time gap. In such cases the decision can be biased due to human intervention. The quiz buzzer presented here takes care of the aforesaid problem. This quiz buzzer disables the other inputs as soon as the first buzzer is pressed. This quiz buzzer can be used for a maximum of eight teams.

EL EVANGELIO SEGUN JESUCRISTO DE SARAMAGO PDF

8 candidate quiz buzzer using 8051 microcontroller (AT89C51)

There is also no need for additional explanation of how these components operate. This is about something commonly unnoticeable when using these components in everyday life. It is about contact bounce- a common problem with m e c h a n i c a l switches. If contact switching does not happen so quickly, several consecutive bounces can be noticed prior to maintain stable state. The reasons for this are: vibrations, slight rough spots and dirt.

DWTT TEST PDF

8 CANDIDATE QUIZ BUZZER USING 8051

The whole design process involves five steps. First step is designing the circuit. The second step is drawing the schematic using any software. Fourth step is programming the microcontroller with the code. Finally, the fifth step is testing the circuit. The microcontroller used in this case is AT89C51, an 8 bit microcontroller manufactured by Atmel now Microchip.

Related Articles