Gogal Fire Trouble is reported to the CS if enabled program question 32, location 3. See the following diagram: For UL installations see wiring diagram for hookup. With this device some systems can obtain dial tone in areas which do not automatically provide dial tone. Keypad Sounder Section 5 — System Operations Fbk Sounder The sounder or loudspeaker housed inside the keypad, emits annunciates sounds according to the condition of the security system.
|Published (Last):||1 June 2012|
|PDF File Size:||1.50 Mb|
|ePub File Size:||17.37 Mb|
|Price:||Free* [*Free Regsitration Required]|
So now i activate the alarm on only a 3 digit code and it is working like that. At the moment telephone line seizure occurs, the Telco Tip is momentary connected to earth ground to access dial tone. The system must be in ready mode. If a keypad tamper code is entered then it will be transmitted to the Central Station.
Got it, progrm to print. LCD display keypads will indicate the following message: This enables Fire and Burg zones to report restores. The purpose of this manual is to give you a brief overview of the XL-2T control xll2t, and provide instructions for installing a basic system. The keypad will indicate a trouble on the fire zone if the bell or sounder is not properly connected. How can i change or dbi rid of this 3 digit code. The following is a quick comparison.
Upon detection of the first violation, smoke detector power on conventional 4 wire smoke detectors connected prgram ZONE modules will be reset for a period of 8 seconds. If selected, then a negative acknowledgment 4 short beeps will be heard after attempting to enter this mode. System ready to be armed System not ready to be armed Select the desired location between wall studs for mounting the keypad. I shall be pleased to learn from you in this regard. We regret any inconvenience this may have caused and appreciate your continued support of FBII products.
Page 70 Section 6 sl2t System Programming When programming the English zone descriptors, use the following techniques to program the characters: The alarm was then activated, without me activating it. System Programming Programming Questions This topic defines the programming questions and the values for each question. The keypads can be surface mounted or flush mounted as described below.
The checkmark highlights which options are selected. To select a trigger type enter the 2 digits in either L1 L2 or L3 L4 desired trigger type for each output trigger. After this time period, power is restored. Some new features have been added and others have been modified.
Enter text from picture: The keypads are surface mounted as described below. If the siren is already sounding, the supervision will not take effect until after bell progeam time. When the switch is pushed toward the front of the keypad, in the opposite direction of the arrowthe switch is in the OFF position. TOP Related.
FBI XL2T PROGRAM PDF
Tojazragore Next, enter the desired account number each digit followed by the key. Pprogram the digit from the table below. Secure keypad to double-gang box as shown in graphic at left. The keypads can be surface mounted or flush mounted as described below. Section 5 — System Operations If a user code is not required to set the time, then enter: Section 5 — System Operations 4. I then pressed code button followed by master codethen user no 3 and then new 4 digit user code. The auto arm time represents the time progtam day that the area will automatically arm if it is not already armed.
Akinotaur There are 36 total questions, with multiple data entry locations. The keypads are surface mounted as described below. Upon detection of the first violation, porgram detector power on conventional 4 wire smoke detectors connected to ZONE modules will be reset for a period of 8 seconds. FBI XL-2T Turbo Program Sheet Separate the two halves of the keypad by placing a straight-slot screwdriver into one of the two slots at the bottom of the keypad and twisting. The alarm was then activated, without me activating it.
So now i activate the alarm on only a 3 digit code and it is working like that. At the moment telephone line seizure occurs, the Telco Tip is momentary connected to earth ground to access dial tone. The system must be in ready mode. If a keypad tamper code is entered then it will be transmitted to the Central Station. Got it, progrm to print.