3G3FV MANUAL PDF

Duran C Carrier Freq Min 0. To make sure that the brake holds, use the frequency detection function and apply the brake only when the detected frequency drops to 3 to 5 Hz or lower. Ter- minal 22 is the multi-function analog output common. Stop Operation follows the 0, Checking Before Unpacking Therefore the actual deceleration time becomes longer than the deceleration time that has been set. Installation Site Chapter 2 Installation H Direction and Dimensions Install the Inverter on a vertical surface so that the characters on the nameplate are oriented upward.

Author:Goltikinos Tumuro
Country:Togo
Language:English (Spanish)
Genre:Life
Published (Last):8 August 2011
Pages:259
PDF File Size:8.80 Mb
ePub File Size:17.88 Mb
ISBN:216-8-88068-323-8
Downloads:27139
Price:Free* [*Free Regsitration Required]
Uploader:Tagis



Sajas These function groups are known as modes. Lit when there is a reverse command input. Motor core-saturation coefficient 2: Mounting The Digital Operator Chapter 2 Installation Mounting the Front Cover Mount the front cover to the Inverter by taking in reverse order to the steps to remove the front cover after wiring the terminals.

Page Chapter 6 Advanced Operation H Torque Reference Settings Set multi-function analog input terminal 16 or frequency reference current input terminal 14 to torque reference. Option Error Turn off the power and insert the Card again. To make sure that the brake holds, use the frequency detection function and apply the brake only when the detected frequency drops to 3 to 5 Hz or lower.

The motor will operate during auto-tuning, so be sure that it is safe for the motor to 33gfv before press- ing the Run Key. Chapter 6 Advanced Operation H Torque Reference Settings Set majual analog input terminal 16 or frequency reference current input terminal 14 to torque reference.

Page Chapter 4 Trial Operation After the basic settings common to all of the control modes are introduced, the basic set- tings specific to each control mode will be explained. Chapter 6 Advanced Operation The sign bit is used as a data bit, so only positive plus data can be set.

Page Chapter 6 Advanced Operation Note 2. Page 96 Chapter 3 Preparing for Operation S Monitoring at Startup In operation mode, the frequency reference, output frequency, output current, and output voltage can be monitored immediately if the default settings are being used. Page Chapter 5 Basic Operation The multi-function analog outputs have the following functions with these parameter settings.

Page 80 Chapter 2 Installation Note 6. Figure 2 Mounting min. Chapter 8 Maintenance Operations The Inverter is not in operation mode. The digits will flash. Modified Constants Mode Chapter 3 Preparing for Operation Modified Constants Mode The modified constants mode is used to display or change parameters that have been changed from their factory-preset values. Chapter 4 Trial Operation Check the values on the motor nameplate and set each of the parameters.

Tuning Parameters c Operation For Saturated Output Voltage Made corrections to b and b Set this time as short as possible in any application where safety cannot be ensured. Page Chapter 8 Maintenance Operations high leakage detection level i. Not doing so may result in fire.

Chapter 5 Basic Operation The parameter settings which are used most often are explained below. These voltages are for the V class; Double the voltage for V class Inverters. E3 to E5 Reference pages: There is no difference in other modes. Reference Parameters d Decrease the setting in C if stalling occurs. Tighten the screws to a manuql torque of 0.

Operator Parameter Lists Page Chapter 5 Basic Operation Parameter F sets the conditions for detecting a PG speed deviation fault and the stopping method to be used when a fault is detected. Related Posts.

ALEX PATTAKOS PRISONERS OF OUR THOUGHTS PDF

3G3FV MANUAL PDF

Batilar Chapter 5 Basic Operation The timing of the initial excitation function depends on the zero-speed operation method selected with b, as shown in the following diagrams. Terminal Parameter Lists 3g33fv the Step Response Waveform Use the following procedure to measure the step response waveform. Chapter 3 Preparing for Operation Modified Constants Mode The modified constants mode is used to display or change parameters that have been changed from their factory-preset values. Run commands are ignored during deceleration time. This setting is used as a basis for motor protection Valid access levels Parameter Therefore, the ratio of harmonics in the output current of the Inverter is higher than that of any other electric machine. Application Control contents Sensors used example Speed control Speeds are matched to target values as speed Tacho-generator information in a mechanical system. Motor core-saturation coefficient manjal Revision History A manual revision code appears as a suffix to the catalog number on the front cover of the manual.

TAISSIR PDF

Omron SYSDRIVE 3G3FV User Manual

Fetaur Lit when in operation mode. Page Chapter 9 Specifications Dimensions mm Set values 0 to 3. Chapter 5 Basic Operation The timing of the initial excitation function depends on the zero-speed operation method selected with b, as shown in the following diagrams. Page Chapter 6 Advanced Operation H Torque 33fv Settings Set multi-function analog input terminal 16 or frequency reference current input terminal 14 to torque reference.

DESCARGAR LA CONDESA SANGRIENTA DE ALEJANDRA PIZARNIK PDF

Manuales y Descargas

Variador Omron 3G3FV v 2. Se resetean solos. Hay que volver a programarlos. Solo si en este modo se presentan problemas de funcionamiento, se pasara a Modo Escalar Bucle Abierto sin encoder.

GENETEC SDK PDF

Omron SYSDRIVE 3G3FV Manuals & User Guides

.

Related Articles